Combi Boiler Installation Setups in Kent Homes
A combi boiler heats the house and the tap water in one wall-hung unit, with no storage tank. The setups below differ by what it's replacing and how it delivers heat.

Replacing a Boiler and a Separate Water Heater
The classic combi job takes out two appliances and puts in one. HomeGuide's $6,000 to $10,000 figure is for exactly this swap. HomeGuide also says combis cost more to install than a standard boiler: more connections, piping and parts, and often a wall mount with special venting. Navien builds the pump into its NCB-H units, so no separate boiler pump is needed.
Combi for Radiant Floor Heat
Radiant floors circulate hot water through tubing under the floor, and HomeGuide lists them with baseboard and radiator systems as the ways a boiler delivers heat. A combi can run a radiant system the same way a standard boiler does. The question for the plumber is whether the existing tubing, manifolds and controls are staying, since those set how much of the job is just the boiler.
Combi With Baseboard Radiators
HomeGuide lists baseboard radiators among the systems a boiler feeds and notes that boilers don't need ductwork. A combi circulates hot water through pipes the way a standard boiler does, so on a replacement the existing baseboard loops are reconnected to the new unit.
Combi Feeding a Hydronic Air Handler
A house with ducts can still run on a combi. Navien describes a hydronic air handler as a cabinet with a coil, pump, blower and controls, connected to the ductwork. When the thermostat calls, hot water from a tankless heater, condensing boiler or combi passes through the coil, and the blower pushes warm air through the ducts. The trade-off Navien points out: while the combi is down for service, there's no heat.
Sizing a Combi for Heat and Hot Water
A combi has two ratings, and they aren't the same number. Navien's NCB-H range shows the gap:
- NCB-190/060H: 60,000 Btu/h for heating, 160,000 for hot water.
- NCB-240/130H: 130,000 Btu/h for heating, 199,900 for hot water.
- NCB-250/150H: 150,000 Btu/h for heating, 210,000 for hot water.
The heating side is sized to the house and the hot-water side to the showers run at once. The hot-water math is the same as for a tankless heater (flow and inlet temperature). Navien's units also ship with a kit to convert from natural gas to propane.

Why Kent homeowners and businesses call Kent Tankless Water Heater
- Your details go to a single independent plumber, not a list of bidders
- The referral is free, and booking is your call
- Ask for gas line, vent and wiring costs as separate lines
- Ask which Kent and L&I permits the job needs
- Keep the down payment small and pay as work is finished
Combi Boiler Installation Cost and What Comes With It
HomeGuide's $6,000 to $10,000 range is for a combi replacing an old boiler or water heater, and its unit prices run from $1,700 to $3,500 (to $4,000 in its gas boiler guide). The spread comes from the house:
Venting
condensing units often need an additional vent and use outdoor air for combustion (tankless venting).Condensate
HomeGuide notes condensing boilers need a condensate pump drain.Gas supply
a combi's hot-water side fires at up to 210,000 Btu/h on Navien's largest model, which the gas pipe has to carry (gas line sizing).Permit
Kent treats heating systems and gas pipes as mechanical work (Kent permits).
On lifespan, HomeGuide gives a gas boiler 10 to 25 years, with high-efficiency models and yearly maintenance at the long end. Navien credits its stainless steel heat exchangers with resisting corrosion.
