Kent Tankless Water Heater logo
Wall-mounted gas tankless water heater with copper water lines, service valves and a white PVC vent in a home garage

Free referral line for Kent, WA

Commercial Water Heater Repair in Kent, WA

  • Typical cost: HomeGuide's national repair ranges are $150 to $700 for a tank and $300 to $1,300 for a tankless unit; they're household figures, so treat them as a floor.
  • Replacement, for comparison: $2,500 to $4,500 installed for most commercial heaters, by A.O. Smith's count.
  • Common parts: a gas control valve runs $150 to $550, a tankless heat exchanger $600 to $1,300.
  • Size line: a heater over 120 gallons or 200,000 Btu input counts as a boiler built to ASME rules, per IAPMO.
  • Food businesses: King County lists no hot water as a reason for immediate closure.

Kent Tankless Water Heater points you to an independent plumber, who quotes the job directly, for a commercial heater that's down or failing. Send the heater's make, size and fuel and what it's doing; a photo of the rating plate helps.

What Breaks on Commercial Water Heaters in Kent

Knowing which of these you have, and its make and size, helps the plumber bring the right parts on the first visit.

Tankless water heater with its front cover off and a gloved hand testing a terminal with a grey multimeter

Large Gas Storage Heaters (75 to 100 Gallons)

Big gas tanks fail the way household tanks do, only with more at stake: the gas control valve, the burner and its flue, sediment on the bottom, and eventually the tank itself. HomeGuide's household figures give a sense of the parts:

  • Gas control valve: $150 to $550.
  • Flue pipe: $100 to $350.
  • Leak from the tank body: replacement, not repair.

For scale, Angi's 2026 averages for replacing a 75-gallon heater run $1,100 to $4,000, and an 80-gallon one $1,300 to $7,500. IAPMO's code manual draws a line at 120 gallons or 200,000 Btu: above either, the heater is classed as a boiler.

Faults on Tankless Racks

A rack or cascade rarely goes fully cold, since the other units keep firing when one locks out. Navien's cascade control brings the next unit on as each reaches 80% of capacity, so one failed unit may first show up only as short supply at the busiest hour. The fault codes and the usual causes, from ignition to scale, are on the tankless repair page.

Booster Heaters

A dish machine that sanitizes with heat needs water hotter than the building supply, so a booster next to the machine raises it the rest of the way. Hatco's Compact booster holds 6 gallons and supplies the 180°F final rinse, with its own relief valve, pressure-reducing valve and high-limit control. Hatco sizes a booster in kW as gallons per hour times the temperature rise, divided by 400, a useful check when a booster can't keep up with a busier machine. The required rinse temperatures are on the restaurant hot water page.

Mixing Valve and Recirculation Loop Problems

Many buildings store water hot and mix it down before it reaches people. Watts cites a recommendation to keep storage at or above 140°F to control Legionella, and describes the ASSE 1017 master mixing valve at the heater as never the only control for water reaching people. The loop pump is what keeps hot water close to far fixtures; HomeGuide prices a replacement recirculating pump at $150 to $680, and how loops work is on the recirculation page.

Power-Vent Blower and Pressure Switch Failures

A power-vent heater pushes its exhaust out with a blower, and a pressure switch shuts the burner off if the vent is blocked. Clear the blockage and the heater restarts on its own, A.O. Smith's manual says, unless it has already gone into lockout. So the vent termination is the first thing to check. Angi notes power venting adds $500 to $1,000 to a replacement over other vent types.

Gloved hands turning a brass service valve under a tankless water heater with a flush hose running into a bucket

Why Kent homeowners and businesses call Kent Tankless Water Heater

  • Your details go to a single independent plumber, not a list of bidders
  • The referral is free, and booking is your call
  • Ask for gas line, vent and wiring costs as separate lines
  • Ask which Kent and L&I permits the job needs
  • Keep the down payment small and pay as work is finished

Get a free tankless water heater estimate

Free for homeowners and businesses. One local contractor contacts you.

Planning for Downtime

The cost of a commercial heater failure is mostly the hours without hot water. Some points to settle before anything breaks:

  • Restaurants and food service

    a kitchen with no hot water can be shut on the spot (the restaurant page has the health department's rule and the food code temperatures). Keep the heater's model and the plumber's number where the closing manager can find them.
  • Rental housing

    Washington gives landlords 24 hours after written notice to start fixing a loss of hot water; see apartment water heaters.
  • Redundancy

    a rack or two smaller heaters can keep part of the supply running during a repair; one large tank can't.
  • Backflow devices

    Kent requires owners to have backflow assemblies tested every year by a state-certified tester. Book that test with the heater service so the water is shut off once.
  • Replace before it fails

    a commercial tank with a leaking body or a cracked heat exchanger is a replacement; Kent permits gas commercial heaters as mechanical work, as set out on the commercial tankless page.

Ready to get started in Kent?

Tell us about the job and a local tankless water heater contractor will get back to you with a free estimate.

Get a free tankless water heater estimate

Free for homeowners and businesses. One local contractor contacts you.