Kent Tankless Water Heater logo
Wall-mounted gas tankless water heater with copper water lines, service valves and a white PVC vent in a home garage

Free referral line for Kent, WA

Commercial Tankless Water Heater Installation in Kent, WA

  • Typical cost: no guide publishes a commercial tankless price. A.O. Smith puts most commercial water heaters at $2,500 to $4,500 installed, and Angi says a light-duty commercial unit runs about $1,000 more than a household one.
  • Rack size: Rinnai's preassembled racks hold up to six 199,000 Btu units and fit through a 32-inch door.
  • Cascades: Navien's controls link up to 32 units, firing the next one when a unit reaches 80% of capacity.
  • Kent permits: a gas water heater goes on a mechanical permit, an electric one on a plumbing permit.

Kent Tankless Water Heater arranges a call back from a single independent plumbing firm for your building's hot water. Tell us the building type, the fixtures that need hot water and what heats it now; the firm quotes the system directly.

How Commercial Tankless Systems Are Built Out in Kent

A commercial system is sized for the busiest hour, not the average one. The first two setups are about how units are grouped; the last three are about the building they serve.

Three tankless water heaters on a steel rack joined by copper manifolds in a commercial kitchen mechanical room

Multi-Unit Rack Systems

A rack mounts several tankless heaters on one frame with shared water and gas headers, so they arrive as one system. Rinnai's Tankless Rack System comes with up to six of its commercial 199,000 Btu condensing units, and its 2012 launch notes said racks can be banked to 25 units. Its specs:

  • Access: fits fully assembled through a 32-inch doorway.
  • Venting: PVC or Rinnai's common vent system.
  • Placement and fuel: indoors or outdoors, on natural gas or propane.

Manifolded Units With Backup Capacity

Units can also be hung on a wall and tied together with manifold kits. Navien's Ready-Link kits come in 30 layouts from 2 to 16 units, with water and gas manifolds, valves and flex lines included. On its NPE-A2 series, the cascade control brings the next unit on when one hits 80% of its capacity and spreads the work across them; Navien lists cascades of up to 32 units. The practical gain is backup: with one unit down for service, the rest keep running. Rinnai makes the same pitch for its racks.

Office and Retail Restrooms

Restrooms in offices and shops use little hot water, scattered across sinks. Often the answer isn't a rack at all but small electric units at each sink, covered on the point-of-use page. Where one central heater does feed a set of lavatories, Watts describes ASSE 1070 valves as the devices that cap the temperature reaching sinks and lavatories.

Warehouses and Light Industrial Sites

Shops that handle corrosive or toxic chemicals may need emergency eyewashes or showers. Washington L&I's guidance for those stations asks for tepid water, single-valve operation and a spot no more than 10 seconds or 50 feet away. Plumbed stations must be tested weekly and inspected yearly. If the station is plumbed into hot water, ask how the design keeps it tepid for the full flushing period.

Gyms and Locker-Room Showers

A locker room puts many showers on at once, which is the load a cascade is built for. Temperature control matters as much as volume. Watts sums up the standards:

  • ASSE 1017: a master mixing valve at the heater, never the only control for water reaching people.
  • ASSE 1069: for gang showers fed at a preset temperature through one pipe.
  • ASSE 1016 / 1070: control at the individual shower or fixture.
Gloved hands turning a brass service valve under a tankless water heater with a flush hose running into a bucket

Why Kent homeowners and businesses call Kent Tankless Water Heater

  • Your details go to a single independent plumber, not a list of bidders
  • The referral is free, and booking is your call
  • Ask for gas line, vent and wiring costs as separate lines
  • Ask which Kent and L&I permits the job needs
  • Keep the down payment small and pay as work is finished

Get a free tankless water heater estimate

Free for homeowners and businesses. One local contractor contacts you.

Kent Permits and Licensing for Commercial Hot Water

Kent splits commercial water heaters by fuel. Its commercial plumbing checklist says gas water heaters are permitted as mechanical work and electric ones under chapter 5 of the plumbing code, which the city enforces as the 2021 Uniform Plumbing Code with Washington amendments. The same checklist asks for the manufacturer's equipment data and installation instructions with the application. It also requires the heaters to be strapped in their upper and lower thirds.

On the gas side, Kent's mechanical checklist asks for an accessible gas shut-off within 6 feet of every gas appliance. Leave a commercial permit's intake fee unpaid for 15 days and Kent cancels the application. Who may do the plumbing in Washington is covered on the water heater repair page; gas supply sizing for a rack is on the gas line page.

Planning Upkeep Before the Rack Goes In

Commercial units run longer hours, and Rinnai's manual doubles the descaling schedule for commercial use in treated hard-water bands, and Kent's figures on the water softener page show where a building falls. Navien sizes its PeakFlow C scale system for commercial jobs up to 20 GPM. Rinnai also strongly recommends isolation valves so each heat exchanger can be flushed. Ask that the quote show them, and where the descaling pump will connect.

Ready to get started in Kent?

Tell us about the job and a local tankless water heater contractor will get back to you with a free estimate.

Get a free tankless water heater estimate

Free for homeowners and businesses. One local contractor contacts you.